Mould Remover Foam SprayHG "mould remover foam spray" immediately destroys mould from damp places - inside and outside. The unique foam formula has a less penetrating odour, can be more easily aimed at the mould and is less likely to splash. The foam formula stays in place longer, making it more effective for a longer period of time. For cleaning tile and plaster walls (also suitable for marble and other natural stone) and for joints in the bathroom, shower, toilet, kitchen, cellar, basement, sauna, swimming pool, garage, and shed. Also cleans facade, balcony, planters, garden statues, etc.
Product information
Mould Remover Foam Spray
HG \mould remover foam spray\ immediately destroys mould from damp places - inside and outside. The unique foam formula has a less penetrating odour, can be more easily aimed at the mould and is less likely to splash. The foam formula stays in place longer, making it more effective for a longer period of time. For cleaning tile and plaster walls (also suitable for marble and other natural stone) and for joints in the bathroom, shower, toilet, kitchen, cellar, basement, sauna, swimming pool, garage, and shed. Also cleans facade, balcony, planters, garden statues, etc.Less penetrating odour, Easier to aim, Less chance of splashing, Better action
Country of Origin
Netherlands
Preparation and Usage
Directions for use: Remove the locking clip before use. If you have used the bottle before, remnants of the liquid may be left in the nozzle, causing it to work less well when you reuse the bottle. Before reusing the bottle, we recommend you rinse the nozzle with hot tap water, e.g. by running the water through the air holes at the side of the foam pipe. The product has a bleaching effect, so in case of doubt start by testing it in a unobtrusive place. Do not remove mould first. Press the nozzle at the front side and turn a quarter. Spray the surface from a distance of 3-5 cm. In case of persistent dirt, spray again after 30 minutes and leave it to work for another 30 minutes. Clean the sprayed surface with water and a sponge. Wash off elastic joints (e.g. silicon sealant) after approx. 30 minutes and spray again. Turn the nozzle a quarter backwards after use (blocking position). For cleaning large surface areas with green deposits we recommend HG algae and mould remover.
Dosage: 2-3 m^2 wall surface, 6-8 m^2 tile joints.
Package Type
Pump
Other Information
Storage:
Transport and store cool, dark and in an upright position.
Keeps longer at lower temperatures.
Safety Warning:
Attention: We recommend you ventilate well during use and wear rubber/plastic gloves. Prevent splashes on clothing, paintwork and vertical blinds. Rinse immediately with water on contact. Prevent contact with metals, such as prints on decorative strips, aluminium and stainless steel. Do not treat coloured surfaces. We do not recommend the use of this product on ceilings. Some permanent brown discolouring may occur after use on light elastic joints (e.g. silicon sealant). You may also see brown colour could be removed with Hypo (sodium thiosulphate) which is available from the costumer service department request. The bottle may not be reused.
Medical personnel can request the data sheet via +31 36 54 94 777.
The consumer's information sheet can be obtained via www.HG.eu
DANGER H314- Causes severe skin burns and eye damage. H410- Very toxic to aquatic life with long lasting effects. EUH206- Warning! Do not use together with other products. May release dangerous gases (chlorine). P101- If medical advice is needed, have product container or label at hand. P102- Keep out of reach of children. P280- Wear protective gloves and eye protection. P303+P361+P353- IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water or shower. P305+P351+P338- IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P501- Dispose of contents and container in accordance with all local, regional, national and international regulations. Contains: Sodium hypochlorite, EINECS: 231-66%-
Importer:
HG Hagesan (UK) Ltd,
Weston Business Centre,
Parsonage Road,
Takeley,
Essex,
CM22 6PU.
Additional Information:
German Consumer Test Institute
Brand
HG
HG Does what it promises.Questions about cleaning and maintenance?
www.HG.eu
Manufacturer
Made by:
HG International b.v.,
Damsluisweg 70,
1332 EJ Almere,
The Netherlands.
Return To Address
HG Hagesan (UK) Ltd,
Weston Business Centre,
Parsonage Road,
Takeley,
Essex,
CM22 6PU.
Tel.: +44 (0) 1206 822 744
Ingredients
Contains a.o.: Anionic Surfactants, Chlorine-Based Bleaching Agents < 5%
We deliver to over 120 countries || Whilst certain products cannot be delivered outside UK, some products may be subject customs and excise duties || We confirm if this product can be delivered to your location (outside the UK) when you enter your delivery address at checkout. If you are unable to checkout, please contact us via WhatsApp or email hello@mcgrocer.com to enquire if this product can be delivered to your location and to process your order via our live chat.
Thanks for subscribing!
This email has been registered!
